View HPWS-TL00_4157858.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Technical Datasheet DS08
SnapLED 150
Introduction
Using Philips Lumileds' patented solderless clinch technology, SnapLED 150 emitters are attached to a formable metal substrate that offers both styling flexibility and ruggedness unmatched by any other LED assembly. Automotive lamp makers can now take advantage of Philips Lumiled's performance stability across a wide current range with a SnapLED 150 option that is optimized and binned for use in dual mode drive current situations such as Automotive Stop/Tail applications using cost effective resistor diode drive circuits. SnapLED's brilliant luminance, flexibility, and reliability enable distinctive and durable lighting designs for vehicles, signals, and specialty lighting.
Key Benefits
Rugged Lighting Products Electricity Savings Maintenance Savings 3 Dimensional Array Design Environmental Conformance
Features
High Luminance Low Power Consumption Low Thermal Resistance Low Profile Solderless Mounting Technique Formable Substrate Meets SAE/ECE/JIS Automotive Color Requirements Packaged in tubes for use with automatic assembly equipment Lead Free RoHS Compliant Dual Mode (Stop/Tail) Option
Typical Applications
Automotive Lighting Rear Combination Lamps Front Turn Signal Lamps High Mount Stop Lamps Indirect Lighting Solid State Lighting and Signaling
HPWS HPWS HPWS HPWS HPWS HPWS
TH00 FH00 TH77 FH77 TL00 FL00
Selection Guide
Table 1
Total Flux V (lm) @ 150 mA[1] Typ. 11.0 Total Included Angle 0.90V (Degrees) [2] Typ. 120 70 120 70 120 70 Viewing Angle 21/2 (Degrees) Typ. 85 30 85 30 85 30
Part Number HPWS HPWS HPWS HPWS TH00 FH00 TH77 FH77
Drive Current Single Mode Single Mode Dual Mode Dual Mode Single Mode Single Mode
LED Color TS AlInGaP Red Orange
HPWS TL00 HPWS FL00
TS AlInGaP Amber
5.5
Notes for Table 1: 1.v is the total luminous flux output as measured with an integrating sphere after the device has stabilized. (RJ A = 100C/W, TA = 25C, Tj ~ 60C.) 2.0.90 V is the included angle at which 90% of the total luminous flux is captured. See Figure 5.
Outline Drawings
Notes: 1.Dimensions are in millimeters (inches). 2.Dimensions without tolerances are nominal. 3.Cathode lead is indicated with a "C" and anode lead is indicated with an "A." 4.Clinch joint locations shown in dashed lines on top view of part (11.50 mm spacing).
SnapLED 150 Technical Datasheet DS08 (01/07)
2
Copyright 2007 Philips Lumileds Lighting Company.
Absolute Maximum Ratings at TA = 25C
Table 2 Parameter DC Forward Current
[1,2] [3] [1]
Rating 150 200 5 473 10 40 to +100 55 to +110 125 (2 hrs.) 125
Units mA mA mA mW V C C C C
Pulsed Forward Current Power Dissipation
Minimum DC Forward Current Reverse Voltage (IR = 100 A) Operating Temperature Range Storage Temperature Range High Temperature Chamber LED Junction Temperature (Tj)
Notes for Table 2: 1. Operation at drive currents below 20 mA is recommended only with dual mode specified LEDs. 2. Derate linearly as shown in Figure 3a. 3. Derate linearly as shown in Figure 3b.
Optical Characteristics at TA = 25C IF = 150 mA, RJ A = 100C/W
Table 3 Total Stabilized Flux v (lm) [1] Typ. 11.0 5.5 Total Instantaneous Flux v (lm) [2] Typ. 12.4 7.2 Ratio of Luminous Intensity to Total Flux Iv(cd)/v(lm) Typ. 0.6 2.0 0.6 2.0 Color, Dominant Wavelength d (nm) [3] Typ. 620 594 Total Included Angle 0.90 V (Degrees) [4] Typ. 120 70 120 70
Device Type HPWS THXX HPWS FHXX HPWS TL00 HPWS FL00
Peak Wavelength peak (nm)[3] Typ. 632 597
Viewing Angle 21/2 (Degrees) Typ. 85 30 85 30
Notes for Table 3: 1.Total Stabilized Flux v is the total luminous flux output as measured with an integrating sphere after the device has stabilized to Tj ~ 60C. 2.Total Instantaneous Flux v is the total luminous flux output as measured with an integrating sphere at 20ms duration. 3. The dominant wavelength is derived from the CIE Chromaticity Diagram and represents the perceived color of the device at Tj ~ 60 C. 4. 0.90 V is the included angle at which 90% of the total luminous flux is captured. See Figure 5.
SnapLED 150 Technical Datasheet DS08 (01/07)
3
Copyright 2007 Philips Lumileds Lighting Company.
Electrical Characteristics at TA=25C
Table 4 Forward Voltage VF (Volts) @ IF = 150mA Device Type HPWS xHxx HPWS xL00 Min 2.19 2.19 Typ 2.8 2.8 Max 3.15 3.15 Reverse Breakdown VR (Volts) @ IR = 100 A Min 10 10 Typ. 20 20 Capacitance C (pF) VF = 0, F = 1MHz. Typ. 80 80 Thermal Resistance RJ PIN (C/W) Typ. 60 75 Speed of Response s (ns) [1] Typ. 20 20
Figures[1]
200 180 1.0
RELATIVE INTENSITY RELATIVE INTENSITY
HPWS-xLxx AMBER
HPWS-xHxx RED-ORANGE
FORWARD CURRENT (mA)
700
160 140 120 100 80 60 40 20
0.5
0.0 550
575
600
625
650
675
0 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2
WAVELENGTH (nm) WAVELENGTH (nm ) Figure 1. Relative Intensity vs. Wavelength.
FORWARD VOLTAGE (V)
Figure 2. Forward Current vs. Forward Voltage.
Figure 3a. Maximum DC Forward Current vs. Ambient Temperature.
Figure 3b. Maximum Pulsed Forward Current vs. Ambient Temperature.
Figure 4. Relative Luminous Flux vs. Forward Current.
1. Figures are Typical unless specified as Maximum.
SnapLED 150 Technical Datasheet DS08 (01/07)
4
Copyright 2007 Philips Lumileds Lighting Company
Figures Continued
[1]
xxx
xxx
Figure 5. HPWS xxxx Percent Total Luminous Flux vs. Total Included Angle. Figure 6a. HPWS Txxx Relative Intensity vs. Off Axis Angle.
Figure 6b. HPWS Fxxx Relative Intensity vs. Off Axis Angle.
Notes for Figures: 1. Figures are Typical unless specified as Maximum. 2. For additional information, please refer to the Philips Lumileds AB20 Series of Application Briefs.
SnapLED 150 Technical Datasheet DS08 (01/07)
5
Copyright 2007 Philips Lumileds Lighting Company.
SnapLED 150 Product Binning
This section provides bin selection assistance for SnapLED 150 LEDs. Additional category and label details for SnapLED product can be found in AB20 7. Product availability varies by color and other factors, and not all bin selection combinations are available. Contact your Philips Lumileds representative for further assistance.
Luminous Flux Bins
High Drive Current (150mA) Minimum Maximum Luminous Flux [2] (lm) Luminous Flux [2] (lm) Low Drive Current [1] (10mA) Minimum Maximum Luminous Flux (lm) Luminous Flux (lm)
Part Number
Bin Code
HPWS FL00 HWPS TL00
HPWS FH00 HWPS TH00
HPWS FH77 HWPS TH77
F G H J L L M N P U V W
3.00 3.50 4.00 5.00 6.00 6.00 8.00 10.00 13.00 7.20 9.40 11.50
4.20 4.80 6.10 7.30 9.70 9.70 12.00 16.00 21.00 11.40 14.10 16.70
N/A N/A N/A N/A N/A N/A N/A N/A N/A 0.50 0.63 0.79
N/A N/A N/A N/A N/A N/A N/A N/A N/A 0.97 1.19 1.43
Note: 1. Dual Mode Drive Current option applies to HPWS xH77 product only. 2.Total Luminous Flux at 150mA as measured with an integrating sphere after the device has stabilized. Tj ~ 60C
Dominant Wavelength Bins, Red Orange
Bin Code
1 2 3
Minimum Dominant Wavelength (nm)
611 615 619
Maximum Dominant Wavelength (nm)
617 621 629
Dominant Wavelength Bins, Amber
Bin Code
1 2 9 3
Minimum Dominant Wavelength (nm)
587 589 592 592
Maximum Dominant Wavelength (nm)
591 594 595 597
SnapLED 150 Technical Datasheet DS08 (01/07)
6
Copyright 2007 Philips Lumileds Lighting Company.
Forward Voltage Bins, High Current (150 mA)
Bin Code
1 2 3 4 5 6 7
Minimum Voltage
2.19 2.31 2.43 2.55 2.67 2.79 2.91
Maximum Voltage
2.43 2.55 2.67 2.79 2.91 3.03 3.15
Forward Voltage Bins, Low Current1 (10 mA)
Bin Code
B C D E F G H
Minimum Voltage
1.84 1.90 1.96 2.02 2.08 2.14 2.20
Maximum Voltage
1.94 2.00 2.06 2.12 2.18 2.24 2.30
1. Low Current Vf Binning applies to HPWS xH77 Dual Mode product only.
SnapLED 150 Technical Datasheet DS08 (11/07)
7
Copyright 2007 Philips Lumileds Lighting Company.
Company Information
Philips Lumileds is a world class supplier of Light Emitting Diodes (LEDs) producing billions of LEDs annually. Philips Lumileds is a fully integrated supplier, producing core LED material in all three base colors (Red, Green, Blue) and White. Philips Lumileds has R&D centers in San Jose, California and in The Netherlands and produc tion capabilities in San Jose and Penang, Malaysia. Founded in 1999, Philips Lumileds is the high flux LED technology leader and is dedi cated to bridging the gap between solid state LED technology and the lighting world. Philips Lumileds technology, LEDs and systems are enabling new applications and markets in the lighting world.
www.luxeon.com www.lumiledsfuture.com
Philips Lumileds may make process or materials changes affecting the perform ance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders.
For technical assistance or the location of your nearest sales office contact any of the following: North America:
1 888 589 3662 americas@futurelightingsolutions.com
Europe:
00 800 443 88 873
europe@futurelightingsolutions.com
Asia Pacific:
800 5864 5337 asia@futurelightingsolutions.com
(c)2007 Philips Lumileds Lighting Company. All rights reserved. Product specifications are subject to change without notice. Luxeon is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries.
Japan:
800 5864 5337 japan@futurelightingsolutions.com

▲Up To Search▲

Price & Availability of HPWS-TL00

	To Download HPWS-TL00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .